Step 1: Open the web browser and type the IP address of the device in the address bar (default is 192.168.1.1). Press Enter.
Step 2: Type the username and password in the login page the default username and password both are admin Then click OK to log into the device.
Step 3: Click on Wireless->Basic on the left side and then configure the basic wireless settings: -> Enable "Enable Wireless" and "SSID Broadcast" -> Enter a name for your wireless network into the SSID box -> Select the correct region which is your country/area.
Step 4: Click Save/Apply to save your settings. Sometimes you might need to reboot your router to active these settings.
I would start by resetting the router to factory defaults this will erase all settings in your router. This is generally done by pressing a paperclip into a very small hole somewhere on the router for usually 10 seconds.
Then hook an ethernet cable up to the router and the other end to your Mac open a web browser and try going to 192.168.1.1. This should bring up the web interface.
At that point you most likely just need to hook up the line coming from your dsl modem into the wan port on the router you probably will need to pull the power on the dsl modem and then plug it back in for the modem to assign an ip to your router.
Your connection is probably working at that point and you can setup whatever other options you need from within the web interface.
Please connect a computer to TP-LINK router by cable or through wireless network. It's recommended to configure it by a wired connection. Log into the router's web-based utility . . .
Step 1: -> Select Wireless -> Wireless Settings on the left side menu to open the wireless setting page. -> Wireless Network Name(also called SSID for some models):Create a new name for your wireless network. If you want to use the default TP-LINK_****** wireless name you can also leave it here as default value. -> Region:Select your current location. -> "Enable Wireless Router Radio" and "Enable SSID Broadcast" should be both ticked. -> Please do not change other settings on this page if not necessary.
Step 2: Click Save to save your settings. Note: After clicking on Save button you will see a tip (red line) at the bottom of the page. But actually there is no need to reboot at here and we will reboot the router at the end of the configurations.
Step 3: -> Select Wireless -> Wireless Security on the left side menu. It's recommended to use WPA/WPA2 Personal(Recommended) some models will name that as WPA-PSK/WPA2-PSK instead. -> Version: WPA-PSK or WPA2-PSK -> Encryption: AES -> Wireless Password(also called PSK Password): make up your WI-FI password also called Wireless Network Key. -> If you want to use WEP as wireless security type you need obey certain rules to create the wireless password.
(A). For 64-bit encryption - You can enter 10 hexadecimal digits (any combination of 0-9 a-f A-F and null key is not permitted) or 5 ASCII characters.
(B). For 128-bit encryption - You can enter 26 hexadecimal digits (any combination of 0-9 a-f A-F and null key is not permitted) or 13 ASCII characters.
(C). For 152-bit encryption - You can enter 32 hexadecimal digits (any combination of 0-9 a-f A-F and null key is not permitted) or 16 ASCII characters.
Step 4: Click Save button to save the settings.
Step 5: Click click here at the bottom of the page to reboot the router; or you can go to system tools reboot to reboot the router to make all settings take effect.
How To Setup TP Link Wireless Router?
Ans: As mentioned in the query, the user has two TP Lin...
Ans: If you wish to know how you can do Tp Link Extende...
Ans: If your ISP is supplying you via DSL (phone line r...
Ans: Step 1: Open web browser and type LAN IP address o...
Ans: Have a computer connected to the router with an et...
|Awarded a Best Answer||10 points|
|Answer Questions||2 points|
|Choose a Best Answer||3 points|