How to Access Linksys Smart Wifi Router Login Page

Fix Linksys Smart Wifi Setup Not Working:

If you wish to setup a Linksys range extender, then you need a Linksys Smart Wi-Fi. The smart Wi-Fi plays a significant role in the setup process of Linksys wireless repeater. Therefore, it is important for you to make sure that the Smart Wi-Fi is working properly. 

Here in this article, you will get to learn all possible reasons responsible for Linksys Smart Wi-Fi setup not working problem. Also, you will learn how to fix this problem. 

Reasons Responsible for Linksys Wi-Fi Setup not Working Problem-

There can be some specific issues that are causing this problem. Mentioned below is the list of problems that can further lead to the problem of Linksys smart Wi-Fi setup not working problem. 

If you come across any of the below stated problems, then you can easily fix the problem by doing a power cycle on your Linksys router. Therefore, you must do a power cycle on your router before you go ahead with other methods to fix the problem. 

However, there are certain cases where the problem does not get fixed by power cycle.  In such cases, you need to take a look at the two major causes of this problem and apply the troubleshooting solutions accordingly. 

Wi-Fi Signal Dropping Frequently

This is one of the common problems leading to the problem of Linksys Wi-Fi setup not working problem. When such a problem occurs, your device starts losing signal frequently. 

There are 4 major reasons that can lead to this problem, these include. 

• Old firmware version 
• Irregular MTU size
• Loss of signal because of interferences
• Weak signal strength

Now that you have read about the problem. Let’s just focus on the solution of the problem. The first problem can easily get resolved by updating the firmware of the Linksys router. To fix the second problem, you can reset the MTU by visiting the settings. 

Third problem can easily be solved by placing the router at some other place. By doing so, you will be able to avoid interferences in signal transmission. 

As far as it is concerned about poor signal strength, you must make sure that there are less number of objects (e.g furniture) in the way, which are making the signal strength bad. You can also change the settings of the Linksys router to fix the last problem. 

Reduced Download Speed

In case you feel that the download speed has slowed down, then this can be happening because of the IPv6 feature. In case you wish to increase the download speed, then this can easily be done by disabling IPv6. To disable IPv6, mentioned below are the steps that you need to carry out. 

Step 1: The first thing that you need to do is to visit the Control Panel. After that, go to the Network and Sharing center. There, click on the option of Change Adapter setting that is given at the left part of your screen. 

Step 2: This will present the list of available networks before you. Go to your Network and then right click on it. After that, select properties. 

Step 3: Then, the local area connection properties screen will be displayed before you. When you go there, you need to check that the Internet Protocol Version 6 is not checked. 

Also, you can take a look at an alternate solution to fix this problem.

• Try performing a firmware update
• In case the problem does not go away, then reset your router.
• Reconfigure your router

In case the issue you are experiencing is not listed above, then you can get in touch with the technical experts. To obtain assistance, all you need to do is to visit the official website of Linksys. 

Solution to Linksys Smart WiFi Setup not Working Problem -

Mentioned below are the steps that you must carry out in order to fix Linksys smart Wi-Fi not working problem. 

1. Configure with the local address that is available to your web address. 
2. Open the router setting
3. After that, go to the setup page
4. Enter the IP address of your router in the location bar of the browser. It is enabled by the web based control panel. 
5. Every Linksys router uses the same default IP address. In case you have changed the IP address of your router, then you don’t have to identify the address in the command prompt. 

After you have entered the IP address, the next thing that you need to do is to follow the commands appearing on the screen. After that, enable WPA2 Personal and enter Admin in the password section. Then, you can set the same password, which was previously set.

Once all is done and the setup is complete, then remove the wire connecting your modem and router. Connect the ethernet wire to the yellow port of the router and connect the router back to the power source. Let it boot completely and complete the booting process. After that, you will be able to acquire the IP address from your ISP.