How to Reset Linksys Range Extender

Reset Linksys Range Extender:

A Linksys range extender is often a helpful way to boost your Wi-Fi signal throughout your building, however you are having to be compelled to do some basic setup before the device is prepared to use it. If your extender stops operating, undergo the Linksys extender reset method to line it back to the default factory settings. 

Here is the step by step guide to Reset Linksys Range Extender:

1. Plug your Linksys Range Extender to the power outlet and wait for 60 seconds.
2. Inside the factory Reset hole of the Linksys Extender and put the paper clip for around 20 seconds; the extender will be still plugged in a wall.
3. Once the light is amber, take the pin out.
4. Now, if you see your device, showing up in your network list by default name i.e. Linksys Extender Setup.
5. Now you can set up your Linksys range extender with the below steps.

Steps to Setup Linksys Range Extender-

Below are the few steps to connect Linksys Range Extender setup through WPS method:

1. First thing you have to do is ensure that your router is configured and that you are able to connect your devices.
2. Now as you plug in the extender to the wall the light blinks green for a few seconds and turns amber after that.
3. Push WPS on the router as soon as the light turns amber and then push the WPS on the extender. (Note:- make sure both devices are in the same room or as close as possible).
4. Now finally, the light on the extender will turn solid green on configuration.

You can also try unplugging the device and plugging it back in to allow it to reboot without having to be reconfigured.

• Or you can also reset the device through the wireless connection, assuming you are able to connect to it. Go to your web browser to connect to the Linksys extender IP address or the extender.linksys.com address at the same time connected to the device. 
• In the menu, click on "Administration," and then "Factory Defaults." 
• Lastly, Click "Restore Factory Defaults." Unplug the extender for 30 seconds, then plug it back in.

Linksys is one in all the famed brands within the Networking devices producing business. Linksys is an American company, and that they sometimes manufacture products for home, used by tiny business users, they are not for the most part into operating with high-end instrumentality and do quite a good job for what they're sensible for. 

Currently they are in hand and operated by Belkin Inc. Actually once we are having an outsized home, wherever it's troublesome for one router to unfold its network, and in those things, we tend to get to check the utilization of various Extenders.

We hope the above article helped you to Reset Linksys Range Extender.

Reset Linksys Range Extender:

Linksys is one of the most known brands in the production industry of networking devices. Linksys is a US-based company. Generally, the products manufactured by this company are for small business users and home users. Now, Linksys is completely operated and owned by Belkin incorporation.

If you recover Linksys range extender, then that means you are going to restore it back to the default settings.

You will be required to reset Linksys range extender in case you come across one of the scenarios mentioned-below:

• In case you are facing intermittent connections at the time of using the range extender.
• You are doing the manual installation of the range extender after going through an unsuccessful attempt of  making use of the setup software.
• You are not able to use the setup page of your Linksys range extender.
• Even after completing the powercycle process, the light of the extender is not blinking.

Before you start with the process of resetting your range extender, then you can make a backup of configuration settings of your device. Restore them without actually performing the process of configuration again.

Mentioned-below are some of the steps that you can follow to understand how to create a backup.

• Open the internet-based setup page of your range extender.
• Now, go to the management sub-tab. Now, go to the button of backup configuration. After that, save the settings.

There are two different methods that you can use for resetting your Linksys range extender.

Press the button of reset placed on the device

The placement of reset button of your range extender depends on the model. Press the reset button of your extender and keep on holding that button for at least 8 seconds. Powercycle the extender device for completion of the reset procedure.

How to soft reset Linksys range extender?

• Open up your internet browser and get an access to the internet-based setup page of the range extender.
• In order to get an access to the internet-based setup page for resetting the range extender, you will be required to connect the PC to the router through wired connection.
• Now, enter the default IP address.
• Enter the username and password for logging in.
• Go to administration and then choose the option of factory defaults.
• Click on the button of restore factory defaults
• For completing the procedure, disconnect the range extender from a power source. Let it remain turned off for 30 seconds.

In case, configuration backup has been created before you reset Linksys range extender back to the default settings. Click on the button of restore configuration, which is given under the sub-tab of Management, then save the settings.

How to hard reset Linksys range extender?

In order to recover range extender these are some steps that you need to follow.

• Turn off your personal computer
• Disconnect your range extender from all the connections.
• Now, link the power wire and boot the range extender
• Once the Linksys range extender starts. Put the paper clip inside the reset hole for a period of at least 20 to 40 seconds.
• If the range extender boots after restarting, then the process to recover linksys range extender will be completed successfully.